caos,
na sajtu sam procitao sjajne upute za VDR i kako ga instalirati pod LinuxOpenSuse10.3
kreuo da pravim kako je tamo opisano, imao poteskoca od samog starta. Tek da na pomenem totalni sam pocetnik po pitanju Linuxa i upravo zbog zelje da isprobam VDR sam se odlucio da se pozabavim pravljenje dual-boot sistema te instalacijom OpenSuse10.3 (do sada se moje iskustvo svodilo na winXP - automatizaciju)..

uspeo sam u ovih para dana da podesim dosta toga u Linuxu (adsl, video kodeci, itd..) veoma sam odusevljen Linuxom. Za sada jos uvek nisam radio na tome da instaliram drajvere bas za moju graficku, jos uvek je ona koju je on sam instalirao ali to mi nije toliko sada presudno slika je sasvim okej i sada, izuzev ne mogucnosti 3D funkcija.

da li bi mogao neko da mi pomogne oko VDR te nekih par saveta bi mi stvarno dobro doslo. Unapred hvala puno, puno

trenutno problem mi je:
# cd ../xine-ui
# patch -p1 < /usr/local/src/VDR/PLUGINS/src/xine/patches/xine-ui.patch
# ./autogen.sh --enable-vdr-keys
# make
# make install

Koji je točno problem u pitanju, koliko vidim, opisao si relativno normalnu proceduru kompajliranja i instaliranja nekog programa koji si pribavio kao source...?

ne dozvoli mi make

Ah, Vlado moj, pa ne bi te ubilo da staviš malo više detalja... Copypaste kompletne poruke o grešci i slično. Jer "ne dozvoli mi make" može značiti bilo što...

adsl:/usr/local/src/xine-cvs/xine-ui # make
make: *** No targets specified and no makefile found. Stop.

tu se javlja problem
# ./autogen.sh --enable-vdr-keys

pokusao sam u pdf-u da posaljem u prethodna dva posta sta se javlja ali izgleda da ne moze da se "zakaci" fajl.

"+ Running aclocal: aclocal: couldn't open directory `/aclocal': No such file or directory
done.
+ Running autoheader: autoheader: error: AC_CONFIG_HEADERS not found in configure.ac
done."

za pocetak ako zelim da obrisem sve sto sam unazad uradio i krenem iz pocetka kako da obrisem.. iz fille browsera to ne mogu da uradim jer mi ne dozvoljava brisanje ali iz konzole se logujem kao root i kako brisem datoteke i fajlove, uninstalliram programe?

adsl:/usr/local/src/xine-cvs/xine-ui # ./autogen.sh –enable-vdr-keys
+ Running aclocal: aclocal: couldn't open directory `/aclocal': No such file or directory
done.
+ Running libtoolize: done.
+ Running autoheader: autoheader: error: AC_CONFIG_HEADERS not found in configure.ac
done.
+ Running automake: configure.ac: no proper invocation of AM_INIT_AUTOMAKE was found.
configure.ac: You should verify that configure.ac invokes AM_INIT_AUTOMAKE,
configure.ac: that aclocal.m4 is present in the top-level directory,
configure.ac: and that aclocal.m4 was recently regenerated (using aclocal).
src/aaui/Makefile.am:4: HAVE_AA does not appear in AM_CONDITIONAL
src/aaui/Makefile.am:8: HAVE_CACA does not appear in AM_CONDITIONAL
/usr/local/share/automake-1.9/am/depend2.am: am__fastdepCC does not appear in
AM_CONDITIONAL
/usr/local/share/automake-1.9/am/depend2.am: AMDEP does not appear in AM_CONDITIONAL
src/common/Makefile.am:7: HAVE_GETOPT_LONG does not appear in AM_CONDITIONAL
src/common/Makefile.am:13: HAVE_X11 does not appear in AM_CONDITIONAL
src/common/Makefile.am:1: Libtool library used but `LIBTOOL' is undefined
src/common/Makefile.am:1:
src/common/Makefile.am:1: The usual way to define `LIBTOOL' is to add `AC_PROG_LIBTOOL'
src/common/Makefile.am:1: to `configure.ac' and run `aclocal' and `autoconf' again.
/usr/local/share/automake-1.9/am/depend2.am: am__fastdepCC does not appear in
AM_CONDITIONAL
/usr/local/share/automake-1.9/am/depend2.am: AMDEP does not appear in AM_CONDITIONAL
src/dfb/Makefile.am:9: HAVE_DIRECTFB does not appear in AM_CONDITIONAL
src/dfb/Makefile.am:15: HAVE_DIRECTFB does not appear in AM_CONDITIONAL
/usr/local/share/automake-1.9/am/depend2.am: am__fastdepCC does not appear in
AM_CONDITIONAL
/usr/local/share/automake-1.9/am/depend2.am: AMDEP does not appear in AM_CONDITIONAL
/usr/local/share/automake-1.9/am/depend2.am: am__fastdepCC does not appear in
AM_CONDITIONAL
/usr/local/share/automake-1.9/am/depend2.am: AMDEP does not appear in AM_CONDITIONAL
src/xitk/Imlib-light/Makefile.am:4: HAVE_X11 does not appear in AM_CONDITIONAL
src/xitk/Imlib-light/Makefile.am:8: Libtool library used but `LIBTOOL' is undefined
src/xitk/Imlib-light/Makefile.am:8:
src/xitk/Imlib-light/Makefile.am:8: The usual way to define `LIBTOOL' is to add
`AC_PROG_LIBTOOL'
src/xitk/Imlib-light/Makefile.am:8: to `configure.ac' and run `aclocal' and `autoconf' again.
/usr/local/share/automake-1.9/am/depend2.am: am__fastdepCC does not appear in
AM_CONDITIONAL
/usr/local/share/automake-1.9/am/depend2.am: AMDEP does not appear in AM_CONDITIONAL
src/xitk/Makefile.am:5: HAVE_READLINE does not appear in AM_CONDITIONAL
src/xitk/Makefile.am:9: HAVE_X11 does not appear in AM_CONDITIONAL
/usr/local/share/automake-1.9/am/depend2.am: am__fastdepCC does not appear in
AM_CONDITIONAL
/usr/local/share/automake-1.9/am/depend2.am: AMDEP does not appear in AM_CONDITIONAL
src/xitk/oxine/Makefile.am:6: HAVE_X11 does not appear in AM_CONDITIONAL
src/xitk/oxine/Makefile.am:10: Libtool library used but `LIBTOOL' is undefined
src/xitk/oxine/Makefile.am:10:
src/xitk/oxine/Makefile.am:10: The usual way to define `LIBTOOL' is to add `AC_PROG_LIBTOOL'
src/xitk/oxine/Makefile.am:10: to `configure.ac' and run `aclocal' and `autoconf' again.
/usr/local/share/automake-1.9/am/depend2.am: am__fastdepCC does not appear in
AM_CONDITIONAL
/usr/local/share/automake-1.9/am/depend2.am: AMDEP does not appear in AM_CONDITIONAL
src/xitk/xine-toolkit/Makefile.am:12: HAVE_X11 does not appear in AM_CONDITIONAL
src/xitk/xine-toolkit/Makefile.am:89: INCLUDED_INTL does not appear in AM_CONDITIONAL
src/xitk/xine-toolkit/Makefile.am:17: Libtool library used but `LIBTOOL' is undefined
src/xitk/xine-toolkit/Makefile.am:17:
src/xitk/xine-toolkit/Makefile.am:17: The usual way to define `LIBTOOL' is to add
`AC_PROG_LIBTOOL'
src/xitk/xine-toolkit/Makefile.am:17: to `configure.ac' and run `aclocal' and `autoconf' again.
/usr/local/share/automake-1.9/am/depend2.am: am__fastdepCC does not appear in
AM_CONDITIONAL
/usr/local/share/automake-1.9/am/depend2.am: AMDEP does not appear in AM_CONDITIONAL
done.
+ Running autoconf: done.
+ Running 'configure --enable-vdr-keys':
checking build system type... i686-suse-linux-gnu
checking host system type... i686-suse-linux-gnu
checking target system type... i686-suse-linux-gnu
./configure: line 1951: syntax error near unexpected token `"xine-ui",'
./configure: line 1951: `AM_INIT_AUTOMAKE("xine-ui", $XINE_MAJOR.$XINE_MINOR.
$XINE_SUB$XINE_PRE)'
adsl:/usr/local/src/xine-cvs/xine-ui # make
make: *** No targets specified and no makefile found. Stop.

Zašto bi stavljao pdfove ako možeš staviti regularni tekst? Čemu to?

Imaš li instalirane autoconf i automake programe? Da li u uputama baš eksplicitno piše da trebaš pokrenuti autogen? Da li piše išta o pokretanju aclocal?

Brisanje većine toga (nakon što je prošao configure) možeš uglavnom sa make dist-clean ili make distclean no autoconf i automake skripte obično samo prepišu postojeće kreirane stvari tako da se oko toga ne trebaš previše brinuti.

U svakom slučaju, po ovim greškama, ili nemaš autoconf i automakegen, ili ako imaš nemaš odgovarajuću verziju, ili patch koji si stavio ne radi kako treba.

ovde se nalaze uputi kako i sta sa VDR-om:
http://www.linux.hr/modules/phpwiki/index.php/Kako%20instalirati%20i%20podesiti%20VDR
po njima sam isao samo sto sam umesto verzije VDR1.4.1 skinuo
verziju 1.5.12

iz YaSTa vidim sledece da mi je instalirano:
installed software
autoconf 2.61
automake 1.10

za ovo je potreban minimalno automake 1.60 koliko vidim,
te sam sam kompajlirao
automake-1.9.6.tar.gz
ali se on ne vidi medju kroz YaST i installed softwar

tako sam ovu prethodnu operaciju zavrsio uspesno:
# cd xine-lib
# patch -p1 < /usr/local/src/VDR/PLUGINS/src/xine/patches/xine-lib.patch
# ./autogen.sh
# make
# make install

ali kod ove sledece, tajac... Greska i nece dalje.
da na pomenem da mi se od xine kodeka pre pokusaja svega ovoga nalazi u Installed software sledece:
amarok-xine 1.4.7
kaffeine 0.8.5 (based xine)
xine-lib 1.1.8
i jos porogramcici u sklopu kojih je xine

daljinac mi je USB-IR te nisam siguran koliko i to igra ulogu..

kada sam ulogovan u root a zelim da obrisem direktorijum recimo VDR ili tako nesto kako to da uradim

jos uvek sam na samom startu ali od necega se mora krenuti..

Tek samo da dodam da je ovo jedan od sjajnih portala za linuxase te da mi se jako dopada :)
pravo mesto za pocetnika.. te hvala puno, puno

da napomenem da sam preko YaST-a pronasao medju
instalacijama VDR 1.4.7 i VDR Plugins

prepustio YaST-u da instalira ali ne mogu da pronadjem gde se sada nalazi VDR i kako da ga pokrenem.
u padajucoj listi instaliran softvera stoji da su uredno instalirani
ali u listi applikacija ga zaista nema..
zato sam odlucio sam kompajlirati i postupiti po uputima..

Citat:

automake 1.10 je noviji od automake 1.9 jer je 10 veći broj od 9.

Citat:

YaST prikazuje samo programe instalirane kao rpm paketi, ne i skompajlirane programe, ako ih nisi pripremio kao rpm pakete. Naime, postoji baza paketa koji su instalirani na osnovu koje YaST zna što ima a što nema.

Citat:

Čekaj malo. Koju si operaciju uspješno napravio a kod koje ti je zapelo? Iz ove priče mi to uopće nije jasno. Kompletno kompajliranje i instalacija po gore navedenim koracima, od ovoga cd xine-lib do make install ti je znači prošla ok?

A jesi ga probao pokrenuti iz komandne linije kao i sve ove fore s kompajliranjem?